Jump to content
Sadikhov IT Certification forums


  • Content Count

  • Joined

  • Last visited

Community Reputation

0 Neutral

About need_to_learn

  • Rank
  1. need_to_learn

    Tagalog? (part2)

    kumusta mga kababayan! tanong ko lang ok ba magwork sa saudi binladin - axal arabia? for network engineer?
  2. need_to_learn

    Help: Issues in simulating ASA in GNS3

    hello makky. sorry just read the mail. i think i put up a security level then it shows in the sho int brief after.
  3. need_to_learn

    IPSEC over GRE VS GRE over IPSEC

    When do we use this kind of command interface Tunnel0 ip address tunnel source tunnel destination tunnel protection ipsec profile TEST tunnel mode ipsec ipv4 i believe this is ipsec over gre???
  4. need_to_learn

    Help: Issues in simulating ASA in GNS3

    sorry, i'm new to asa. i just resolved it.
  5. need_to_learn

    cisco switch to AP configuration

    Hello sirkozz and Kunal Thank you very much for the info! appreciate it!
  6. need_to_learn

    Help: Issues in simulating ASA in GNS3

    I changed the nic to pcnet but its still not showing the ip address that I configured but in the running config its there interface Ethernet0/0 no nameif no security-level ip address ! asa(config)# sho int ip brie Interface IP-Address OK? Method Status Protocol Ethernet0/0 unassigned YES manual up up Ethernet0/1 unassigned YES unset administratively down up Ethernet0/2 unassigned YES unset administratively down up Ethernet0/3 unassigned YES unset administratively down up Ethernet0/4 unassigned YES unset administratively down up Ethernet0/5 unassigned YES unset administratively down up asa(config)# sho int e0/0 Interface Ethernet0/0 "", is up, line protocol is up Hardware is linaeth, BW 10000 Mbps, DLY 10 usec Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps) Media-type configured as RJ45 connector Available but not configured via nameif MAC address 0000.abc9.4a00, MTU not set IP address, subnet mask 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 L2 decode drops 0 packets output, 0 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 babbles, 0 late collisions, 0 deferred 0 lost carrier, 0 no carrier input queue (curr/max packets): hardware (128/128) software (0/0) output queue (curr/max packets): hardware (0/0) software (0/0) what is the problem with this???? thanks for the help
  7. need_to_learn


    Maybe the ff is the correct way of doing it? neighbor { import as-path-prepend; export as-path-prepend;
  8. need_to_learn


    neighbor route-map VZBCER in neighbor route-map VZBCER out inbound/outbound policy with Cisco commands above is the same with importing/exporting a policy statement in Junos? So it will look like this? ====================== group VZBCE { type external; local-address; export as-path-prepend and import as-path-prepend????? peer-as 55000; neighbor; ======================= import as-path-prepend export as-path-prepend ======================= policy-options { policy-statement as-path-prepend { term prepend { from { route-filter orlonger; route-filter orlonger; route-filter orlonger; } then as-path-prepend "1 1 1 1"; }
  9. need_to_learn


    Hi chrcel, Thank you very much!
  10. need_to_learn


    Can someone show me how to configure the below cisco commands to Junos? Thank you. route-map ATTCER permit 10 set as-path prepend 64660 64660 64660 64660 64660 ! route-map VZBCER permit 10 set as-path prepend 64660 64660 64660 64660
  11. Need your inputs about this Wireless connection to AP. Let's say I have L2 cisco switch and I will connect it to an AP, what is the recommended configuration for that? Core Switch ---- L2 cisco switch --- AP I know theres a lot of docs from cisco and from google but I want to hear it from all the experienced engineers on wireless. Thank y'll!
  12. need_to_learn


    Hi, I need to ask how many calls can be run in the frame-relay 512kbps bandwidth with g.729 codec? How do you compute that? Thanks!
  13. need_to_learn

    Large Site WAN Design Review, Please?

    yeah I can see that your network is very critical That's the important, configuring your CE to PE for BFD and from CE to core switch. if you don't configure the bfd from ce to pe and you are using ebgp (very slow) I am sure you will have a 1 - 2 min of down time which is not good! I'm not really familiar with ethernetflow forgive me. Once you implement it with your CE1 - PE (BFD) no need to configure the BFD on CE2 - PE because once the primary goes up it should be seamless. Remember this is just based on my experience and this is just a suggestion Good luck with your Design. Critical one.
  14. need_to_learn

    Large Site WAN Design Review, Please?

    This is just a suggestion: If you want to have seamless failover when the primary link goes down OR both of your MPLS links goes down you need to configure BFD on all interfaces participating to outbound traffic. If your service provider is capable of configuring BFD on their PE that is great because somet of them can't support it or don't want to configure it maybe?. I'm working with a call center company and the voice is very critical for us. So when the primary mpls circuit goes down it is seamless meaning the call center agents while they are on the call and the circuit goes down data/voice don't drop that's because of the BFD. eBGP from CE to PE OSPF from CE to Core Switch
  15. need_to_learn

    Prefix-list Accept and Advertise Routes to the Neighbor Router

    got it now. Thank y'll!