Jump to content
Sadikhov IT Certification forums

superr

Members
  • Content count

    217
  • Joined

  • Last visited

Community Reputation

1 Neutral

About superr

  • Rank
    Advanced Member
  • Birthday 10/10/1984

Profile Information

  • Gender
    Male
  • Location
    Dubai
  1. One of the cisco agent call state is not showing in Supervisor desktop .Configurations are all same like other agents
  2. SPAN based call recording is not working for 6921 phone When the same extension is configured on 7960 phone on same port its working fine We are using witness call recorder
  3. No Recording Option

    Builtin bridge is der for 7960 but still no recording option ):
  4. I want to enable k based SIP based recording for some cisco ip phones 7960 and 7940. Eabled buildtin bridge on device settings.But there is no recrording option available on line Recording profile is available for 7911 phones Why it is not coming for 7960 and 7940 ?
  5. got it Its under clusterwideparameters in service parameters of ccm Incoming calling party national number prefix
  6. Hi We have a CCM 4.1 with H.323 VG. E1 PRI Theres is no translation profile for incoming calls and no translation pattern on callmanager when i called my extension from mob prefix 9 is automatically added to my mob Telco is sending the number without 9 on ISDN confused These are the pots and voip dialpeer matched during the call dial-peer voice 20 pots tone ringback alert-no-PI incoming called-number 4... direct-inward-dial port 1/0:15 ! dial-peer voice 30 voip tone ringback alert-no-PI destination-pattern 4... voice-class h323 1 session target ipv4:192.168.4.100 dtmf-relay h245-alphanumeric codec g711ulaw no vad
  7. cdr enterprise parameter

    Hi Thanks now its working fine with stone voice call accounting
  8. Hi, Sometimes im getting flapping ISDN link detected by trap on our voice gateway. wat could be the issue VG#sh isdn status Global ISDN Switchtype = primary-net5 ISDN Serial1/0:15 interface dsl 0, interface ISDN Switchtype = primary-net5 Layer 1 Status: ACTIVE Layer 2 Status: TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED Layer 3 Status: 11 Active Layer 3 Call(s) VG#sh isdn service PRI Channel Statistics: ISDN Se1/0:15, Channel [1-31] Configured Isdn Interface (dsl) 0 Channel State (0=Idle 1=Proposed 2=Busy 3=Reserved 4=Restart 5=Maint_Pend) Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 State : 0 0 2 0 0 0 0 0 0 0 0 0 0 0 0 3 0 0 0 2 0 2 0 2 2 2 2 2 2 2 2 Service State (0=Inservice 1=Maint 2=Outofservice 8=MaintPend 9=OOSPend) Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 State : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  9. Hi, I want to change cdr format to flat file in enterprise parameters. Will it require any restart of the service? will there be any problem since its a production
  10. Hi, I want to upgrade my ccm 4.1(3)sr7 to CUCM 8.2 How can it be done.Whats the procedure to do that . .its a production netw Regards
  11. how to pickup calls in ucs 560.
  12. backup entire flash

    Thanks Mark .Super Command
  13. Hi , I want remote users to connect to the office network using dialup acess.what is the best possible solution
  14. How can i backup entire content of flash for my voice router in one shot .Is there any tcl script ?
  15. call forward

    call forward all is configured and i tried the reset.
×