Jump to content


Ipv6 Rs (ccnp642-901)


  • Please log in to reply
4 replies to this topic

#1 aami

aami

    Newbie

  • Members
  • Pip
  • 27 posts

Posted 26 May 2008 - 02:30 AM

Pls confirm what is IPV6 router Solicitation ,


A) A request made by node for the IP address of router ,

B) A request made by node for its IP address ,

P4Sure says A

But as per me it should be B ,

Pls verify ,

Thanks,
Amit
  • 1

#2 upen singh

upen singh

    Advanced Member

  • Members
  • PipPipPip
  • 363 posts
  • Gender:Male
  • Location:India
  • Interests:Cisco Cisco Cisco....................

Posted 26 May 2008 - 02:32 AM

QUOTE (aami @ May 26 2008, 03:30 AM) <{POST_SNAPBACK}>
Pls confirm what is IPV6 router Solicitation ,


A) A request made by node for the IP address of router ,

B) A request made by node for its IP address ,

P4Sure says A

But as per me it should be B ,

Pls verify ,

Thanks,
Amit




Hi

p4s is correct because this qs was in my exam (BSCI) and i got 1000/1000 points

thanks
  • 0

#3 balaji_m_r

balaji_m_r

    Newbie

  • Members
  • Pip
  • 10 posts

Posted 26 May 2008 - 03:31 AM

QUOTE (aami @ May 25 2008, 10:00 PM) <{POST_SNAPBACK}>
Pls confirm what is IPV6 router Solicitation ,


A) A request made by node for the IP address of router ,

B) A request made by node for its IP address ,

P4Sure says A

But as per me it should be B ,

Pls verify ,

Thanks,
Amit



hi the ans in P4S is correct, becoz the router will not giv the ip address to the host rather it will provide only the prefix for the host, then the host will use the prefix & its interface identifier builds its ip address,So P4S is correct, i got 1000/1000 in this exam
  • 0

#4 Lord Flasheart

Lord Flasheart

    All Rise For The Lord

  • Veterans
  • PipPipPipPipPip
  • 2848 posts
  • Gender:Male
  • Location:England

Posted 26 May 2008 - 10:09 PM

Just another point of view on this from a post I made a little while back.

You've got to be careful here with the wording - the router does not send the node an IP address for that node, it sends a prefix. Therefore Answer B is incorrect. The router sends its prefix and then the node adds its interface ID to make its own IPv6 address, thus Answer A is correct.

The following is the actual procedure for IPv6 stateless address autoconfiguration:

(1) The new node on the network generates link local address and allocates it to the interface. Link-local address takes the following form: fe80:0000:0000:0000:0000:

(2) The node confirms that generated link local address is not already used on the same network (DAD: Duplicate Address Detection). At first, the node transmits Neighbor Solicitation (NS) message on the network. If another node is already using the same address, this node sends Neighbor Advertisement (NA) message. The new node that transmitted NS message will use the original link-local address if it receives no NA message after a certain time. If the new node is notified of the duplicate address situation, it will not allocate the link-local address and terminates the interface.

(3) The new node sends Router Solicitation (RS) message on the network to request information, using the link-local address just allocated. RS message transmission is not a must. The node can passively wait for (4).

(4) The node that received RS message (usually a router) sends back Router Advertisement (RA) message. RA message is transmitted periodically, so nodes do not necessarily have to send RS message.

(5) The node receives RA and gets IPv6 address prefix.

(6) The node forms the global IPv6 address by combining prefix and interface ID, just as it did for link-local address.

It should be noted that RA sender, such as router, only sends fixed prefix allocated to the network. In other words, RA sender does not care to whom it sent information. It does not maintain such records. Therefore, if two routers exist on the same network and advertise different prefixes with RAs, receiving node automatically gets both RA to allocate different address on the same interface.
  • 0

#5 aami

aami

    Newbie

  • Members
  • Pip
  • 27 posts

Posted 29 May 2008 - 02:23 AM

Thanks a lot for your reply ,
  • 0





0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users